Expert Answers about Mercury Grand Marquis
- Transmission Cooler Installation Tips for a 1994 Mercury Grand Marquis LS
- The Derale Series 8000 Plate-Fin Transmission Cooler Kit, # D13503, would be a great choice for your 1994 Mercury Grand Marquis, as long as there is room in front of the radiator and ac condenser for the cooler to mount. Measure to be sure before purchasing, but most likely you will have plenty of room.
The best tip I can give is to do some research on your vehicle. Check the radiator fittings and see if there are NPT (national pipe thread) fittings or Inverted flare fittings. Your vehicle...
view full answer... - How to Install Hopkins Universal Trailer Wiring Harness on a 2011 Mercury Grand Marquis
- Universal trailer wiring harnesses such as # 46255 do not have vehicle specific installation instructions but it isn't difficult to install this harness. All you will have to do is determine the functions of the vehicle tail light wiring using a circuit tester such as # PTW2993 or a meter if you have one.
On the harness, the white wire is ground. Attach it to a clean bare metal surface. The yellow wire will go to the left turn signal/brake light wire on your 2011 Mercury Grand Marquis....
view full answer... - What Modifications Need to be Made to Install Curt Hitch # C121030 on a 2002 Mercury Grand Marquis
- You will need to relocate the exhaust pipe hanger on the passenger side to accommodate your dual exhaust on your 2002 Mercury Grand Marquis. There is a hole in the plate bracket of the Curt Hitch # C12130 that will allow you to do this.
Aside from that you will need to drill holes in the frame of your 2002 Mercury Grand for the mounting hardware to secure this hitch to the vehicle.
view full answer... - Where To Install Manual Air Inflation Valves From Firestone Coil-Rite Air Helper Springs # F4107
- On the Firestone Coil-Rite Air Helper Springs - Rear Kit, part # F4107, the inflation valves need to be installed in a protected area that is easily accessible. You might check inside the trunk area to see if there is a place where the inflation valve can be installed. You will need to drill a 5/16 inch hole for the inflation valve. If you drill a hole in the trunk area I would recommend to use a sealer when installing the valve to keep exhaust fumes and debris from entering the trunk area.
If...
view full answer... - Moving Exhaust Hanger On 2002 Mercury Grand Marquis W/ Dual Exhaust To Install Curt Hitch 13707
- We have not had a chance to install the Curt Trailer Hitch # 13707 on a 2002 Mercury Grand Marquis with dual exhaust so I do not have a picture of video to show you, but it will be pretty straight forward and obvious how much and where to relocate the exhaust hanger while installing the hitch. There is not an exact measurement or place it needs to be moved to, just where ever clears the hitch.
The mechanic you are taking the vehicle to for the install will be able to modify the hanger...
view full answer... - Do Body Panels have to be Removed to Install a Trailer Hitch on a 2008 Mercury Grand Marquis
- You should not have to remove any body panels to install Curt trailer hitch # 13707 on your 2008 Mercury Grand Marquis. I have included a link to the installation instructions and a video showing installation for you to view.
If you plan on doing some towing I recommend etrailer ball mount kit # EBMK4EL. It comes with an extra long ball mount (a long ball is required on this vehicle due to the position of the hitch), interchangeable ball set, hitch pin with clip, and a storage bag.
For...
view full answer... - How Many Watts Does 12 Volt Heater PTW5009 Draw and is it Ceramic
- Heater # PTW5009 draws 13 amps at 12 volts which equals out to about 156 watts. I did a little research and from what I could find it is not ceramic.
view full answer... - Recommended Class III Trailer Hitch Receiver That is Most Hidden on a 2004 Mercury Marquis
- We carry two Class III trailer hitch receivers that will fit your 2004 Mercury Grand Marquis. A Curt, # 13707, and a Draw-Tite, # 41116.
Both of them are basically the same style and the only thing you'll see under the car's bumper is the receiver opening and safety chain loops.
Between the two I recommend the Curt because it has a little higher weight capacity than the Draw-Tite. But for appearance purposes they'll basically be the same.
view full answer... - Driving in Reverse with Fastway e2 Weight Distribution with Sway Control
- You made a great choice! The e2 Weight Distribution Hitch, # FA94-00-1000, is a sturdy system that has 2-Point Sway Control and comes with a 10-year warranty. The unique design of this system does allow you to back up without having to disconnect the sway bars.
Don't give your friends a hard time, though. Many weight distribution systems have independent friction sway control devices that do require you to get out of your vehicle and remove the device prior to backing up. Your e2 system,...
view full answer... - Difficulty of Relocating Exhaust Hanger for Hitch Installation on 1999 Mercury Grand Marquis LS
- Installation of the Curt Class III trailer hitch # 13707 that you referenced will require exhaust hanger modification on your 1999 Mercury Grand Marquis LS with dual exhaust. The hanger is essentially a steel rod that connects with a rubber shock mount to the exhaust. The steel hanger is what will need to be relocated. This is best done by a qualified welder and will allow enough clearance between the exhaust and the hitch. The process is not especially complicated but for safety reasons...
view full answer...
Go To Results